Allstar Products Group Garage Door Opener 8822 User Manual

STEP 4: CHECK OUT YOUR DOOR OPERATING SYSTEM  
Installation Instructions  
CAUTION: THERE ARE NO USER SERVICEABLE PARTS INSIDE  
TRANSMITTER OR RECEIVER  
A. After installing your receiver and transmitter, check the operation of your radio  
controls by moving approximately 35 feet back from the garage door, then press  
the transmitter button. Operation at this distance should be reliable.  
B. If the transmitter doesn’t activate the operator, check the coding switches on both  
the transmitter and receiver to assure an “exact” match. (See Fig. 2 & 3). This  
may necessitate a reprogramming of a Quik Code Classic transmitter to match the  
receiver coding switches.  
Garage Door and Gate Operator Radio Controls  
Models 9921, 9931, 8822, 8832, 8833  
C. If the distance is inadequate, check the battery and replace if necessary. (Also See  
Step 4D).  
Proper installation of your radio controls will assure  
years of trouble-free operation.  
D. To maximize the operating distance move the transmitter to different locations in  
the car until a satisfactory distance is achieved.  
E. If the receiver is in the proximity of a metal beam or other obstruction it may be  
necessary to relocate the receiver to increase the operating range.  
READ THE FOLLOWING INSTRUCTIONS  
THOROUGHLY BEFORE STARTING INSTALLATION  
F. If multiple receivers are mounted closer than 15 feet, blocking and  
interference may occur. Relocate the receivers farther apart.  
STEP 1: SET YOUR CODING SWITCHES  
G. If system does not work at any distance, check that the receiver terminals are  
connected to the proper operator terminals. See Step 2A.  
CAUTION: THE FACTORY PRESET CODE MUST BE  
CHANGED TO SAFEGUARD AGAINST UNAUTHORIZED  
OPERATION.  
Manufacturer’s Limited Warranty  
104384  
Allstar warrants its radio controls to be free from defect in material and workmanship for a  
period of one (1) year from the date of purchase. To obtain service, contact your dealer.  
To obtain service under this warranty the buyer must obtain authorization instructions for the  
return of any goods from Allstar before returning the goods. The goods must be returned with  
complete identification, with copy of proof-of-purchase, freight prepaid and in accordance  
with Allstar’s instructions or they will not be accepted. In no event will Allstar be responsible  
for goods returned without proper authorization or identification.  
A. Remove the access cover from the front of the  
transmitter by sliding the cover away from the top of  
the transmitter. (See Fig. 1A).  
Goods returned to Allstar for warranty repair within the warranty period, which upon receipt  
by Allstar are confirmed to be defective and covered by this limited warranty, will be repaired  
or replaced at Allstar’s sole option, at no cost and returned pre-paid. Defective parts will be  
repaired or replaced with new or factory rebuilt parts at Allstar’s sole option.  
TRANSMITTER  
B. Use a small screwdriver or knife to remove small  
door on back of receiver to gain access to coding  
switches. (See Fig. 1B)  
Figure 1A  
104385  
This limited warranty does not cover non-defect damage, damage caused by unreasonable use,  
damage caused by improper installation or care, vandalism or lightning, fire or excessive heat,  
flood or other acts of God (including, but not limited to misuse, abuse or alterations, failure to  
provide reasonable and necessary maintenance), labor charges for dismantling or reinstalling a  
repaired or replaced unit, or replacement batteries.  
IMPORTANT: THE EXACT SAME CODE MUST  
BE SET ON BOTH THE TRANSMITTER AND  
RECEIVER. IF JUST ONE SWITCH IS  
MISMATCHED THE CONTROLS WILL NOT  
FUNCTION.  
These warranties are in lieu of all other warranties, either expressed or implied. All implied  
warranties of merchantability and/or fitness for a particular purpose are hereby disclaimed and  
excluded. Under no circumstances shall Allstar be liable for consequential, incidental or  
special damages arising in connection with the use or inability to use this product. In no event  
shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability  
exceed the cost of the product covered hereby. No person is authorized to assume for Allstar  
any other liability in connection with the sale of this product.  
RECEIVER  
Figure 1B  
Note:  
If installing Allstar Classic Quik Code transmitter(s) with a 99xx or 88xx  
This warranty gives you specific legal rights. You may also have other rights which vary from  
state to state. Warranty effective after July 1, 1998.  
Allstar Receiver, first set your receiver coding switches to your private code setting  
using the instructions that follow THEN program your Allstar Classic Quik Code  
transmitter (following the instructions included with the transmitter) to match the  
receiver.  
For Information:  
Phone 610-873-6900  
FAX 610-873-6953  
PART #107713 REV C  
 

Abocom Network Router FSW410 User Manual
Acer Laptop VDA0307001 User Manual
Addonics Technologies Computer Hardware ADSA3GPX8 ML User Manual
Addonics Technologies Copier DGC11 User Manual
ADTRAN Network Card 3125 Gigabit Ethernet User Manual
AEG Washer L 87480 FL User Manual
Aiphone Intercom System CC 1M User Manual
Alienware Personal Computer M18X R2 User Manual
ATI Technologies Wheelchair SR 101 User Manual
Behringer Microphone MIC200 User Manual